1.04 GBd low EMI digital video interface system using small swingserial link technique

In a high-resolution flat panel system, a conventional interface that directly connects a liquid crystal display (LCD) controller to a flat panel cannot overcome the problems of excess EMI (electromagnetic interference) and power caused by full-swing transmission signals in parallel lines. This paper presents a high-speed digital video interface system implemented with a low-cost standard CMOS (complimentary metal-oxide-semiconductor) technology that can mitigate EMI and power problems in high-resolution flat panel display systems. The combined architecture of the high-speed, small number of parallel lines and low-voltage swing serial interface can support resolutions from VGA (640×480 pixels) up to XGA (1024×768 pixels) with significant power improvement and drastic EMI reduction. To support high-speed, low-voltage swing signaling and overcome channel-to-channel skew problems, a robust data recovery system is required. The proposed digital phase-locked loop enables robust skew-insensitive data recovery of up to 1.04 GBd     

A 200-MHz complex number multiplier using redundant binaryarithmetic

Modern digital communication systems rely heavily on baseband signal processing for in-phase and quadrature (I-Q) channels, and complex number processing in low-voltage CMOS has become a necessity for channel equalization, timing recovery, modulation, and demodulation. In this work, redundant binary (RB) arithmetic is applied to complex number multiplication for the first time so that an N-bit parallel complex number multiplier can be reduced to two RE multiplications (i.e., an addition of N RB partial products) corresponding to real and imaginary parts, respectively. This efficient RE encoding scheme proposed can generate RB partial products with no additional hardware and delay overheads. A prototype 8-bit complex number multiplier containing 11.5 K transistors is integrated on 1.05×1.33 mm² using 0.8 μm CMOS. The chip consumes 90 mW with 2.5 V supply when clocked at 200 MHz     

Rapidly tunable optical add-drop multiplexer utilising relaxed beam splitters

A polarisation-independent four-port electro-optic tunable filter in the 1530 nm wavelength regime utilising non-polarising relaxed beam splitters and strain-induced polarisation converters on LiNbO₃ with 16 nm tuning range and 46 ns tuning speed is reported.     

Fatigue crack propagation properties from small sized rod specimens

Mechanical properties characterization is needed in many industrial applications yet sufficient amount of material for fabricating standard-sized testing specimens is often not available. Techniques for testing miniaturized specimen must be adopted. Much effort has been made to develop techniques for impact, fracture toughness and tensile properties of sub-sized specimens. Work on the testing of fatigue properties is more limited. In this study, fatigue crack propagation behavior is evaluated from the growth of surface crack in a cylindrical rod under tension. Rods of various lengths and diameters were tested. As the size of the rod specimen is reduced, the fatigue crack growth rate tends to increase when correlated using the stress intensity factor range. This increase is explained largely by the decrease in the degree of premature crack closure in the small specimens. Valid fatigue crack growth data can be obtained among the specimens examined except on the crack growth on the surface of the smallest specimen, which has a length of 26 mm and diameter of 8 mm. Even so, valid data can still be elucidated on the latter specimen if the interior growth is considered. The dimensions of the latter specimen allow fatigue properties to be evaluated using broken remnants from impact or other test specimens.     

Chemical vapor deposition of amorphous ruthenium-phosphorus alloy films

Chemical vapor deposition growth of amorphous ruthenium-phosphorus films on SiO₂ containing ∼ 15% phosphorus is reported. cis-Ruthenium(II)dihydridotetrakis-(trimethylphosphine), cis-RuH₂(PMe₃)₄ (Me = CH₃) was used at growth temperatures ranging from 525 to 575 K. Both Ru and P are zero-valent. The films are metastable, becoming increasingly more polycrystalline upon annealing to 775 and 975 K. Surface studies illustrate that demethylation is quite efficient near 560 K. Precursor adsorption at 135 K or 210 K and heating reveal the precursor undergoes a complex decomposition process in which the hydride and trimethylphosphine ligands are lost at temperatures as low at 280 K. Phosphorus and its manner of incorporation appear responsible for the amorphous-like character. Molecular dynamics simulations are presented to suggest the local structure in the films and the causes for phosphorus stabilizing the amorphous phase.     

At least N+1 finite transmission zeros using frequency-variant negative source-load coupling

A second-order cross-coupled combline filter which has three finite transmission zeros is presented. The problem of the frequency-invariant coupling in a real circuit is introduced. To make extra transmission zeros, a top metalized dielectric block is used.     

The stress-whitened damage zone of PVC blends

The stress-whitened damage zone that formed ahead of a semicircular notch during slow tensile loading has been measured from optical micrographs of translucent blends of poly(vinyl chloride) (PVC) with experimental chlorinated polyethylene (CPE) resins. When the zone was small, the plane strain condition applied and from the elastic stress distribution a constant mean stress condition was found at the boundary of the crescent-shaped zone. The critical mean stress did not depend on the chlorine content or the chlorine distribution of the experimental CPE resin used in the blend. While the critical mean stress decreased as the amount of CPE in the blend was increased, the critical volume strain, calculated from the bulk modulus, was independent of composition and was thought to be the controlling parameter for stress-whitening. When the zone was larger, the shape was qualitatively described by concepts of stress redistribution in the presence of a plastic zone ahead of the notch. Macroscopic flow and necking were only detected near the maximum in the stress-displacement curve.